CSM | PE WRAPPING TRIAL & ACCEPTANCE PREPARATION
Blank English record | Revision 2026-10-11
https://colorsteelmachine.com/resources/pe-wrapping-trial-acceptance-preparation/
This is a preparation sheet, not a completed trial report or acceptance certificate.
No default pass limits, equipment operating instructions or safety-validation protocol are supplied.
Use "Not agreed", "Not tested" or "Not reviewed" for outstanding items. Blank does not mean pass.

1. AGREED SCOPE
Project/reference:
Quotation/configuration revision:
Trial location/date:
Supplier/customer participants and designated reviewers:
Standalone wrapper / linked line:
Equipment and interfaces present:
Included functions:
Excluded checks and later site checks:
Agreed sample count and job mix:
Applicable supplier operating/safeguarding procedures:

2. SAMPLE RECORD (repeat per sample)
Sample ID / production job / requested minimum, typical or maximum:
Panel type / count / surface finish:
Complete travelling length / width / height (units):
Complete bundle weight (units):
Measurement method / measured, estimated or unknown:
Supports / edge protectors / end covers / protrusions:
Support sketch and end-view filename/revision:
Agreed usable passage width / height / datum and drawing revision:
Written complete-bundle fit review / clearance conditions / unresolved items:
Pre-trial surface, edge and alignment photo filenames:
Protection material supplier / grade / batch:

3. FINISH REQUIREMENTS (agree before trial)
Requirement ID:
Side coverage and overlap requirement:
Film start/finish and exposed-end requirement:
Separate end protection or strapping task and responsible party:
Surface/edge condition requirement:
Support and alignment requirement:
Agreed observation or measurement method:
Agreed criterion and conditions:
Reviewer:
No waterproofing, transport restraint or automatic end sealing is inferred.

4. RUN RECORD (repeat per run; create a new ID for changes)
Run ID / sample ID / setup revision:
Date/location/qualified operator:
Film supplier / grade / batch / stated thickness and units:
Actual control labels, settings and units as recorded by operator:
Ring speed reference:
Conveyor speed reference:
Overlap reference:
Film tension reference:
Film start/finish / cutting / sealing / roll-change tasks actually included:
Manual tasks / stops / retries:
If output measurement is agreed: start/finish definitions and conditions:
Measured time, spacing, removal time and evidence:
Continuous video filename / any edited summary identified separately:
Before/after photo filenames:
Actual observations:
Changes since previous run:
No prescribed settings or accepted bundles-per-hour value is supplied.

5. LINKED-LINE HANDOVER (where included)
Interface drawing revision:
Bundle-ready / transfer conditions:
Actual arrival and removal method:
Conveyor direction / heights / support locations:
Upstream/downstream equipment present:
Control responsibilities and included interfaces:
Manual tasks and responsible party:
Handover evidence filenames:
Absent interfaces / outstanding site checks:
Safeguarding checks are governed by the qualified supplier's agreed protocol.

6. REQUIREMENT RESULT (repeat per requirement)
Requirement ID / agreed criterion / method / conditions:
Measurement references where needed:
Related run IDs:
Observed result:
Evidence filenames:
Reviewer assessment: Not reviewed / Pass / Fail / Not tested / Other (explain):
Issue / exception:
Action owner / required action:
Agreed repeat-trial or site-check scope:
Changed configuration or material revision:

7. REVIEW OUTCOME
Evidence pack index and revision:
Open issues and agreed actions:
Named reviewers / dates:
Recorded decision:
Contractual acceptance responsibilities and approval reference:
Until designated review occurs, mark "Not reviewed".
Factory trial, site commissioning and contractual acceptance are separate agreed scopes.
Visual finish review is not transit certification or proof of weatherproofing.
Distribution testing advice, if required, must address the complete package and actual conditions.

CONFIGURATION DIMENSIONS - NOT TRIAL PASS LIMITS
Documented package section: 1200 x 1200 mm; package length: 16000 mm.
Conveying surface height: 1200 mm; confirm measurement datum, not bundle height.
Overall dimensions: 35000 x 2500 x 2600 mm; not usable passage dimensions.
A separate maximum usable package height is not confirmed in the source brief.
1250 mm requested bundle height is 50 mm above documented package height; fit unresolved.
The proposed 2.5 m gantry stacking height is not the wrapper working height.
Obtain the usable-passage drawing and written fit review before the relevant trial.

Equipment: https://colorsteelmachine.com/machines/pe-wrapping-machine/
Selection inputs: https://colorsteelmachine.com/resources/pe-wrapping-machine-inputs/
Enquiry: https://colorsteelmachine.com/?product=Full-Stack%20PE%20Wrapping%20Machine#inquiry