Questions & answers
Frequently asked questions
Answers collected from every machine, guide and company page on this site, grouped by topic. Each answer links to the page it comes from.
Machines and specifications
54 questions from 10 pages
Column-Type Integrated Panel Feeding Machine
Does a listed material mean every grade can be picked?
Each grade is checked. Send the actual grade, board construction, dimensions, weight and both faces; pickup tooling is matched to your boards during project review.
Source page: Column-Type Integrated Panel Feeding Machine
Does the catalogue speed guarantee my line output?
No. It is an approximate presentation value. Keep output discussions tied to the actual material, complete feeding sequence, replenishment and receiving-line availability.
Source page: Column-Type Integrated Panel Feeding Machine
Can I calculate the installation footprint from the listed dimensions?
No. The original presentation gives height and width but no overall length. Request the complete project layout and agreed travel/interface scope; do not infer the missing dimension.
Source page: Column-Type Integrated Panel Feeding Machine
Is stacked-board feeding the same as rock wool strip continuation?
No. This page describes pickup and transfer from stacked flat core boards. Prepared-strip continuation has a different incoming arrangement and placement task. Use the continuation input guide for that route.
Source page: Column-Type Integrated Panel Feeding Machine
Automatic C/Z Purlin Turnover-Arm Stacker
What is the maximum lifting weight per individual profile?
300 kg per individual profile. Choose MCZ-Z-400-10 when each profile weighs 300 kg or less; section geometry, tooling and bundle arrangement are matched to your profiles.
Source page: Automatic C/Z Purlin Turnover-Arm Stacker
What profile sizes does MCZ-Z-400-10 cover?
The supplied specification states C, U and Z profiles with lengths of 3,000–13,000 mm, widths of 100–400 mm, thicknesses of 1.5–5 mm and a “waist height” of 40–125 mm. Confirm dimension labels and the complete section geometry on your drawing.
Source page: Automatic C/Z Purlin Turnover-Arm Stacker
How does the turnover sequence work?
The profile is conveyed into position and precisely located. Gripping and placement complete the first layer. The following-layer sequence includes turnover before gripping and placement, repeating until the stack is complete.
Source page: Automatic C/Z Purlin Turnover-Arm Stacker
Can stack columns and layers be adjusted?
Yes. Stack columns and layers can be adjusted within the designed range; stack height and bundle pattern are set for your sections.
Source page: Automatic C/Z Purlin Turnover-Arm Stacker
What power and compressed-air facilities are listed?
The document lists 7.5 kW installed power and a required 3 kW air compressor with a 100 L tank. It does not state air pressure or consumption; agree those utility details for the project.
Source page: Automatic C/Z Purlin Turnover-Arm Stacker
What delivery time is stated?
Delivery is 20 days after receipt of the deposit.
Source page: Automatic C/Z Purlin Turnover-Arm Stacker
What production rate can I expect?
Production rate depends on profile length and arrival interval. Send the actual arrival intervals, profile lengths and full-stack removal arrangement, and the configuration is matched to your line output.
Source page: Automatic C/Z Purlin Turnover-Arm Stacker
Is this a sandwich-panel vacuum stacker?
No. This product uses profile gripping and mechanical turnover. Vacuum-cup quantities, panel load ratings and sandwich-panel handling parameters are not its specifications.
Source page: Automatic C/Z Purlin Turnover-Arm Stacker
How do I send drawings?
Download the blank project-input TXT sheet and email authorised drawing references. The website enquiry form does not accept attachments.
Source page: Automatic C/Z Purlin Turnover-Arm Stacker
Automatic Floor Deck Turnover Stacker
Is this a vacuum suction-cup stacker?
No. This page describes the mechanical floor-deck turnover equipment shown in the source presentation: opposed arms, receiving rollers and servo motions. Vacuum panel handling parameters are not transferred to this machine.
Source page: Automatic Floor Deck Turnover Stacker
Do 575 / 600 mm mean overall and effective width?
Send a section drawing with separately labelled overall sheet width and effective cover width, so the 575 / 600 mm entries are matched to your profile.
Source page: Automatic Floor Deck Turnover Stacker
Does the approximate 25-second cycle guarantee line output?
The nominal cycle is approx. 25 s. Provide sheet length, line speed, arrival sequence, requested turnover and full-stack exchange conditions, and the stacker is configured to your line output.
Source page: Automatic Floor Deck Turnover Stacker
How should I identify the incoming and finished faces?
Label Face A and Face B on your actual section, show the incoming upward face and travel direction, then draw the requested completed stack.
Source page: Automatic Floor Deck Turnover Stacker
Are bundling and automatic stack removal included?
Describe the full-stack supports, quantity, orientation and removal method, and identify the next-process owner. Bundling and stack removal are listed as separate scope items.
Source page: Automatic Floor Deck Turnover Stacker
What should I send with a configuration enquiry?
Send your actual profile drawing, gauge, separately labelled widths, length range, line layout, face requirements and proposed full-stack handover. Use the input sheet and detailed support guide below to organise those materials.
Source page: Automatic Floor Deck Turnover Stacker
Gantry Flipping & Stacking Machine
Which panels can the gantry flipping stacker handle?
The documented configuration is intended for corrugated long-span panels, polyurethane (PU) sandwich panels and cleanroom panels. Vacuum suitability and the final tooling arrangement must be confirmed against the actual profile, surface and weight.
Source page: Gantry Flipping & Stacking Machine
What panel sizes are covered?
The source document lists panel lengths from 4,000 to 15,000 mm and pickup widths of 950, 960, 1,050 or 1,200 mm. The supported panel thickness is 50–200 mm (5–20 cm).
Source page: Gantry Flipping & Stacking Machine
How fast is the stacking cycle?
The documented cycle time is 20–30 seconds per panel. Final output depends on panel characteristics, the flip sequence, line interface and required stack pattern.
Source page: Gantry Flipping & Stacking Machine
What information is needed for a proposal?
Provide panel drawings, size and weight range, contact surface, line discharge height, stack pattern, available footprint, cycle target and site utilities.
Source page: Gantry Flipping & Stacking Machine
Gantry Rock Wool Continuation Machine
Does this route include rock wool cutting?
Describe how prepared strips reach the continuation machine and list upstream cutting as a separate scope item where needed.
Source page: Gantry Rock Wool Continuation Machine
Is 420 m/h a guaranteed line output?
No. It is the approximate value in the source presentation. Sustained project output requires an agreed basis covering the actual material, placement pattern, replenishment and interruptions.
Source page: Gantry Rock Wool Continuation Machine
Do the frame dimensions approve an installed layout?
The frame outline is 5.20 × 1.65 × 2.50 m. Travel, installed clearance and interfaces are laid out for your line from your layout, obstructions and receiving conditions.
Source page: Gantry Rock Wool Continuation Machine
Is prepared-strip continuation the same as full-board feeding?
No universal equivalence is claimed. Identify the actual incoming material and review the column-type panel feeding route separately when the project starts with full boards.
Source page: Gantry Rock Wool Continuation Machine
PE Wrapping Machine for Sandwich Panel Stacks
Is this a PE wrapper or a strapping machine?
This page describes horizontal orbital wrapping of a complete panel stack with PE film. Steel- or plastic-strap binding is a separate machine and scope.
Source page: PE Wrapping Machine for Sandwich Panel Stacks
Does it build or flip the panel stack?
No stacking or flipping function is stated in this source. The packaging machine receives a prepared stack from an upstream process.
Source page: PE Wrapping Machine for Sandwich Panel Stacks
Is the load 2,800 kg or 3,000 kg?
The source brief requests a stack weighing approximately 2,800 kg. Its equipment parameter table lists a 3,000 kg effective load. They are different values with different meanings, not interchangeable ratings.
Source page: PE Wrapping Machine for Sandwich Panel Stacks
Does 5–10 m/min mean finished packages per hour?
It is the conveyor speed. Completed-stack output is calculated from wrapping settings, stack length, spacing and transfer and removal time.
Source page: PE Wrapping Machine for Sandwich Panel Stacks
Are film cutting, sealing and end-face coverage included?
These details are specified with your required film and finished-package standard before quotation.
Source page: PE Wrapping Machine for Sandwich Panel Stacks
What is the maximum package height?
The documented configuration has a 1,200 mm package height. The machine’s 2,600 mm external height and the upstream stacker’s 2.5 m stacking height are separate values. Request the passage drawing for your complete bundle; a 1,250 mm bundle is 50 mm above the documented package height.
Source page: PE Wrapping Machine for Sandwich Panel Stacks
Can it connect directly to a CSM stacker?
A connection is a project integration question, not an automatic compatibility claim. Confirm stack dimensions and weight, transfer height, conveyor layout, controls and responsibility at both sides of the handover.
Source page: PE Wrapping Machine for Sandwich Panel Stacks
Automatic Purlin Cleat Plate Welding Machine
Does the presentation range confirm my part will fit?
Fixture and welding programme are matched to your part drawing and weld specification; the listed values are the presentation specifications.
Source page: Automatic Purlin Cleat Plate Welding Machine
Is this a universal fabrication robot?
No. The existing application description is for repeated purlin-cleat and small connection-plate assemblies with stable datum points and weld locations. Sample parts, weld procedure and inspection criteria should be agreed before fixture manufacture.
Source page: Automatic Purlin Cleat Plate Welding Machine
Is welding travel speed the same as finished-parts output?
No production rate is established by the approximate adjustable welding speed listed here. Provide your required output and discuss incoming preparation and counting boundaries using the project-input sheet.
Source page: Automatic Purlin Cleat Plate Welding Machine
Can the download sheet approve weld quality?
The blank sheets organise purchasing information and evidence responsibilities. Welding settings and acceptance limits are set in the agreed protocol and reports.
Source page: Automatic Purlin Cleat Plate Welding Machine
Robotic Rock Wool Continuation Machine
Does ±0.05 mm mean rock wool is placed that accurately?
The presentation lists ±0.05 mm repeat positioning and, separately, 1 mm continuation accuracy. The finished-panel tolerance is defined with your project measurement conditions.
Source page: Robotic Rock Wool Continuation Machine
Can the machine always carry 30 kg of rock wool?
Ask what the stated maximum payload covers and request the proposed tooling, mounting, carried material and attached-items load summary.
Source page: Robotic Rock Wool Continuation Machine
Does the working radius approve the complete cell layout?
The radius and equipment outline are presentation values. Send the actual pickup and receiving positions, tooling, material and layout revision, and the cell is laid out for your line.
Source page: Robotic Rock Wool Continuation Machine
Is approximately 400 m/h sustainable project output?
Not automatically. It is the nominal presentation figure. A project response needs a stated material, pattern and timing basis, including how replenishment, changeovers and receiving-line interruptions are treated.
Source page: Robotic Rock Wool Continuation Machine
Sandwich Panel Stackers
How does the stacker synchronize with the sandwich panel production line speed?
The stacker does not need to run continuously at exactly the same speed as the sandwich panel production machine.
After the panel is produced and cut to length, it enters the stacker infeed conveyor. The conveyor accelerates and transfers the panel to the pickup position under the stacking gripper. When the position sensor detects the panel, the conveyor stops automatically. The gripper then picks up the panel and completes the required turnover and stacking operation.
Source page: Sandwich Panel Stackers
Which solution should I discuss?
For 2,500–12,000 mm panels, discuss the 20261007 single unit with stacking only or turnover plus stacking. Above 12 m without turnover, request a project review of single-unit stacking. Above 12 m with turnover, discuss two synchronized linked units. Width, weight, thickness, material and profile must also be confirmed.
Source page: Sandwich Panel Stackers
What is the maximum individual panel working weight?
The standard single-unit 20261007 machine has a maximum individual panel working weight of 240 kg; heavier panels are handled with a customized configuration. Panel width, thickness, core, profile and handling sequence are matched to your line.
Source page: Sandwich Panel Stackers
Does the 12 m range mean longer panels cannot be stacked?
It describes the single-unit normal turnover and stacking range. Longer-panel stacking-only configurations are reviewed for each project.
Source page: Sandwich Panel Stackers
What must be confirmed for the dual-unit solution?
Maximum panel length, width, weight and thickness combinations, core and profile compatibility, unit spacing and support, synchronization, cycle rate, stack height, controls and site interfaces are configured for each project. The video shows the synchronized process.
Source page: Sandwich Panel Stackers
Does the 2,500 mm stack height apply to dual units?
That figure is documented for the 20261007 single unit. Confirm the target stack height and permitted panel combinations separately for a synchronized dual-unit proposal.
Source page: Sandwich Panel Stackers
Does stacking include wrapping and finished-bundle removal?
Only when the quotation explicitly includes those tasks and equipment. Supply the required stack arrangement, removal method and each interface owner separately.
Source page: Sandwich Panel Stackers
Can I use the S04 gantry vacuum stacker ratings for S01?
They are separate catalogue machines with their own specifications. Send your actual panel combinations for the S01 proposal.
Source page: Sandwich Panel Stackers
Tie-Rod Cutting & Welding Machines
What distinguishes integrated and welding-only equipment?
The documented integrated configuration includes a plasma cutting station. Welding-only receives prepared components from upstream and excludes that station. Identify the actual incoming condition and itemise included functions before selection.
Source page: Tie-Rod Cutting & Welding Machines
Does welding-only always need less installation space?
Incoming stock, workpiece handling, service arrangements and downstream handover are included in the project layout.
Source page: Tie-Rod Cutting & Welding Machines
Which welding power-source package applies to welding-only?
The presentation slides disagree. The original disclosure in the configuration section is retained; this page does not choose between the ratings. The final quotation must identify the selected package.
Read the original package disclosure.
Source page: Tie-Rod Cutting & Welding Machines
Can the preparation sheet approve the assembly or weld quality?
No. The blank sheets collect project and evidence references, not acceptance limits or sign-off. Use actual drawings, the agreed scope and separate project protocols and reports with the responsible reviewers.
Source page: Tie-Rod Cutting & Welding Machines
Project preparation and buying
72 questions from 20 pages
Automated Welding Acceptance Preparation
Does a successful machine demonstration qualify the weld?
The responsible project personnel determine what the demonstration and the supporting evidence cover.
Source page: Automated Welding Acceptance Preparation
Can a generic checklist replace the project's criteria?
No. The approved project documents govern. This sheet only helps organise information before those requirements are agreed.
Source page: Automated Welding Acceptance Preparation
What needs clarification for W02 welding-only equipment?
The presentation contains different welding-only power-source packages. The selected package is stated in the final proposal; see the tie-rod product page.
Source page: Automated Welding Acceptance Preparation
Automation FAQ & Glossary
Does a shorter cycle prove higher line output?
Agree the operation boundaries, workpiece count and arrival conditions first; line output is calculated from those records. Keep them in the output-claim checklist.
Source page: Automation FAQ & Glossary
Is a payload rating enough to select a robot?
No. Identify the tooling and carried items and provide the load-analysis inputs described above. A headline rating or reach is not application approval.
Source page: Automation FAQ & Glossary
Does automatic stacking include automatic changeover?
Not by definition. Ask about stacking and product changeover separately, and record each inclusion or unresolved item in the written scope.
Source page: Automation FAQ & Glossary
Automation Machine Quotation Checklist
Can I start when some project inputs are missing?
Yes, mark missing fields unknown and describe the current task. A preliminary enquiry can identify what is needed; it does not settle configuration, compatibility or acceptance commitments.
Source page: Automation Machine Quotation Checklist
Does a base-machine price include every conveyor and service?
Ask each supplier to mark the same scope items included, optional, excluded or awaiting information, then confirm the agreed scope in writing.
Source page: Automation Machine Quotation Checklist
Does the checklist approve a production rate?
Tie each supplier output statement to actual workpieces, pieces per cycle, timing boundaries, replenishment, stack removal and the stated evidence type.
Source page: Automation Machine Quotation Checklist
Column Panel Feeder: Selection Input Guide
Is this the same task as rock wool strip continuation?
No. This brief describes transfer from a stack of flat core boards. Prepared-strip continuation has a different incoming arrangement and placement pattern.
Source page: Column Panel Feeder: Selection Input Guide
Does listing a material mean all its grades can be picked?
No. Specify the actual grade, faces, dimensions, weight and sample condition for tooling review.
Source page: Column Panel Feeder: Selection Input Guide
Does the catalogue speed guarantee my line output?
No. Keep output discussions tied to the material, complete feeding sequence, replenishment and receiving-line availability.
Source page: Column Panel Feeder: Selection Input Guide
Does selection confirm panel strength or fire performance?
No. This is factory-handling preparation, not a material certification or finished-panel approval.
Source page: Column Panel Feeder: Selection Input Guide
Project Input Sheets & Forms
Which form should I use if I am not sure about the machine?
Start with the common project checklist and record actual workpieces and line conditions. Mark unknowns as TBD, then add the relevant process sheet or request a line review.
Source page: Project Input Sheets & Forms
Does filling or downloading a form send it to CSM?
No. Save and reopen your copy to check it. Send a summary through the contact route; the web form does not accept attachments. Follow the email route above for authorised drawings or videos.
Source page: Project Input Sheets & Forms
Is a product brochure the same as a project input form?
No. A brochure provides information about its named model. The blank forms collect your own project inputs; they are not machine manuals, capacity approval or acceptance records.
Source page: Project Input Sheets & Forms
Feeder & Stacker Retrofit Checklist
Does adding a feeder or stacker confirm line compatibility?
Line compatibility is assessed for the project from the actual material, interfaces, production sequence, layout and controls.
Source page: Feeder & Stacker Retrofit Checklist
Can a machine outline define the installed clearance?
Request a project layout with installation footprint and safety distances.
Source page: Feeder & Stacker Retrofit Checklist
Can I complete the brief with missing drawings?
Record available drawing revisions and mark missing information TBD with a responsible contact.
Source page: Feeder & Stacker Retrofit Checklist
Gantry Panel Stacker FAT & Acceptance Checklist
Does the 41-second product video prove acceptance?
The video on the product page shows the machine in operation. Test load, representative output and signed acceptance are recorded during the project acceptance.
Source page: Gantry Panel Stacker FAT & Acceptance Checklist
Can this checklist replace an operating manual?
No. Only delivered-machine documentation and approved procedures should be used for operation, maintenance and safety-related testing.
Source page: Gantry Panel Stacker FAT & Acceptance Checklist
What if an extreme panel was not available at FAT?
Record the untested case and agree how suitability will be confirmed. Do not sign an untested product family off by analogy without the responsible team's approval.
Source page: Gantry Panel Stacker FAT & Acceptance Checklist
Gantry vs Robotic Rock Wool Feeding
Do 420 and 400 m/h prove a production advantage?
No. They are listed manufacturer-presentation figures, not a controlled head-to-head test or a guaranteed line-output comparison.
Source page: Gantry vs Robotic Rock Wool Feeding
Does the same brief mean both arrangements are compatible?
Each proposal is configured with its own material, tooling, layout and timing review.
Source page: Gantry vs Robotic Rock Wool Feeding
Is the robotic arrangement always the smaller installed cell?
No. Keep machine outline and complete installed area separate, including loading, guarding and maintenance requirements.
Source page: Gantry vs Robotic Rock Wool Feeding
Long Sandwich Panels: Stacking or Dual Turnover
Can one unit stack any length above 12 m?
Stacking-only single-unit arrangements above 12 m are reviewed with the actual panel, support and line, and the maximum and permitted combinations are stated in the proposal.
Source page: Long Sandwich Panels: Stacking or Dual Turnover
Does a 15 m panel automatically require two units?
Above 12 m with turnover, use synchronized dual units. Without turnover, request a single-unit stacking-only review. Width, weight, stiffness, profile and site interfaces complete the configuration.
Source page: Long Sandwich Panels: Stacking or Dual Turnover
Can I copy the S04 450 kg load or 20–30 second cycle?
S04 is a separate gantry vacuum machine with its own ratings; S01 single-unit and dual-unit capability is stated separately.
Source page: Long Sandwich Panels: Stacking or Dual Turnover
Does the video establish the final arrangement?
It illustrates a movement sequence. The project proposal must define the panel combinations, unit spacing, support, controls, performance evidence and site layout.
Source page: Long Sandwich Panels: Stacking or Dual Turnover
PE Wrapping: Stack, Film & Handover Inputs
What should I send for a PE wrapping quotation?
Send the minimum, typical and maximum finished-bundle dimensions and weight, a labelled end view, protective supports, film-roll details, the requested packaging finish, arrival intervals, conveyor heights and the removal method. Label measured, requested and unknown values separately.
Source page: PE Wrapping: Stack, Film & Handover Inputs
Is ring diameter the same as usable package width?
A bundle has both width and height, and protective materials enlarge its envelope. Ask for the usable passage drawing and operating clearance for the complete envelope.
Source page: PE Wrapping: Stack, Film & Handover Inputs
Does PE wrapping mean waterproof or sealed ends?
Side wrapping, end protection and fully closed packaging are different requirements. State the required coverage and storage conditions so end sealing and weatherproofing are specified.
Source page: PE Wrapping: Stack, Film & Handover Inputs
Does automatic mode include automatic film cutting?
Not necessarily. The supplied configuration states manual and automatic modes, but does not specify automatic film clamping, cutting, sealing or roll change. Confirm each function separately in the quotation.
Source page: PE Wrapping: Stack, Film & Handover Inputs
Can conveyor speed be converted to finished bundles per hour?
Not on its own. Record bundle length, spacing, wrapping pattern, start and finish operations, arrival intervals and removal time. The documented 5–10 m/min is conveyor speed, not an acceptance-tested packaging rate.
Source page: PE Wrapping: Stack, Film & Handover Inputs
Can a 1250 mm bundle use the published 1200 mm height?
That fit has not been confirmed. The requested bundle is 50 mm higher than the documented standard package height. Agree a revised usable aperture or a lower finished-bundle target; do not treat a small difference as clearance.
Source page: PE Wrapping: Stack, Film & Handover Inputs
PE Wrapping Trial & Acceptance Preparation
Is the trial record an acceptance certificate?
It is a blank preparation and evidence sheet. Acceptance uses the agreed criteria, recorded results and approval by the designated parties.
Source page: PE Wrapping Trial & Acceptance Preparation
How many sample bundles should we prepare?
Agree the sample count and job mix with the supplier, using representative production bundles across the requested range.
Source page: PE Wrapping Trial & Acceptance Preparation
Does a good-looking wrap prove transport protection?
Visual finish review covers appearance. Weatherproofing, load restraint and transport performance are assessed separately with packaging-test advice for your distribution conditions.
Source page: PE Wrapping Trial & Acceptance Preparation
Can conveyor speed prove packaging output?
Agree the measured cycle boundaries and include film start and finish, manual tasks, stops, bundle spacing and removal time. The finished-bundle rate is calculated from those records.
Source page: PE Wrapping Trial & Acceptance Preparation
Does automatic mode confirm film cutting or sealing?
Clamping, cutting, sealing, roll change and any manual tasks are listed in the written trial scope.
Source page: PE Wrapping Trial & Acceptance Preparation
What if film, supports or bundle construction changes?
Create a new run ID and record the changed revision. Review whether the previous result still applies and agree the repeat-trial scope; do not silently reuse an earlier approval.
Source page: PE Wrapping Trial & Acceptance Preparation
C/Z Purlin & Metal Deck Stacking Guide
Read the planning notes
Our current catalogue lists separate machines for C/Z purlins and floor deck sheets. They have different workpiece geometries and handling arrangements. Selecting by material length alone overlooks the cross-section, support positions and required turning motion.
This guide covers factory outfeed and stacking. Building spans, load capacity and the structural choice between C and Z sections belong to the project’s structural design, not to the stacker specification.
Source page: C/Z Purlin & Metal Deck Stacking Guide
Read the planning notes
Show the purlin as it exits the roll former, including which way its open side faces. Provide the intended layer arrangement and bundle size. For floor deck sheets, show the profile, contact points and required face-up or face-down sequence.
ASC’s product page separately discusses C-section exit orientation, cycle conditions and bundle staging. These are useful issues to ask about; its supported profiles and options are not our machine specifications.
Source page: C/Z Purlin & Metal Deck Stacking Guide
Read the planning notes
Use the shortest production length and fastest actual arrival interval when checking demanding operating conditions. Include any time needed to clear a full stack. A nominal roll-forming speed cannot by itself establish how frequently the stacker must pick up a part.
Map the complete route from cutting discharge to bundle removal. Identify available buffering, the movement of forklifts or other removal equipment, and whether removal interrupts stacking. Required buffers and protective measures are engineering decisions for the actual layout.
Source page: C/Z Purlin & Metal Deck Stacking Guide
Read the planning notes
- Which changes are recipe settings and which require mechanical adjustment?
- What tooling is needed for each approved section?
- Which components are wear items, and what part identifiers appear in the manual?
- Which electrical and pneumatic items are included in the final package?
- What evidence demonstrates the agreed profile range before dispatch?
Send a section drawing, minimum and maximum lengths, material gauge, individual weight, discharge height and bundle-removal plan. Different manufacturers’ parts should not be assumed interchangeable because their catalogue descriptions sound similar.
Source page: C/Z Purlin & Metal Deck Stacking Guide
Purlin Cleat Welding: Drawing & Fixture Inputs
Can I request a quote with photographs only?
Photographs can start the conversation, but mark the request as preliminary. Final fixture configuration needs the agreed component and assembly information.
Source page: Purlin Cleat Welding: Drawing & Fixture Inputs
Does twin-gun welding automatically double finished output?
No fixed output multiplier is established here. A representative cycle also includes loading, locating, clamping, any required movements and unloading. Agree the timing boundaries and part mix before comparing output.
Source page: Purlin Cleat Welding: Drawing & Fixture Inputs
Where should trial documents be agreed?
Use the welding evidence preparation guide to identify the documents and responsible reviewers before the proposed trial. It does not supply pass limits.
Source page: Purlin Cleat Welding: Drawing & Fixture Inputs
Rock Wool Continuation: Project Input Guide
Does continuation include cutting slabs into lamellas?
Identify cutting and preparation as separate scope items and ask which equipment is included.
Source page: Rock Wool Continuation: Project Input Guide
Can I submit the same sheet for both arrangements?
Yes. Use the same material and receiving requirements, then add the arrangement-specific layout inputs above. This supports a comparable proposal.
Source page: Rock Wool Continuation: Project Input Guide
Does the feeder determine the finished panel’s strength or fire rating?
Feeder selection and panel-system assessment are separate. Material selection, bonding and finished-panel requirements have their own review.
Source page: Rock Wool Continuation: Project Input Guide
Sandwich Panel Handling & Stacking Guide
Read the planning detail
Panel geometry and the intended stack come first. Record whether the product is a flat wall panel or a profiled roof panel, its length, width, thickness and weight, and the permitted contact areas. Then show the stack orientation required for storage, wrapping or dispatch.
“Sandwich panel” here means a metal-faced building panel produced in a factory. Installation lifting equipment, aircraft composite panels and board presses have different tasks and should not be compared as equivalent stackers.
Source page: Sandwich Panel Handling & Stacking Guide
Read the planning detail
Turnover depends on the panel profile and the approved stacking arrangement. Ribs and surface finishes can affect how neighbouring panels sit together. KINDUS discusses turnover for corrugated roof panels, illustrating why the profile drawing matters.
Our sandwich-panel presentation describes both turnover and non-turnover configurations. Send a cross-section and the desired stack arrangement before choosing between them.
Source page: Sandwich Panel Handling & Stacking Guide
Read the planning detail
| Method | What needs checking? |
|---|---|
| Vacuum handling | Accessible pickup surface, seal quality, profile, coating, protective film and behaviour during the intended motion. |
| Mechanical handling | Accessible support or gripping areas, edge condition, part stiffness and clearance during pickup and release. |
Both methods appear in KINDUS’s equipment description. Our tooling and contact method are stated in the selected machine proposal.
Source page: Sandwich Panel Handling & Stacking Guide
Read the planning detail
The current S01 product 20261007 has a normal 2,500–12,000 mm single-unit range for stacking only or turnover plus stacking, with a recorded 0–2,500 mm single-unit stack height. Over 12 m without turnover, request a stacking-only single-unit project review. Over 12 m with turnover, discuss synchronized dual units.
Dual-unit length, load, spacing, cycle and stack height are set in the proposal. See the long-panel decision guide and current S01 input guide.
Stack height is not panel thickness. These S01 routes do not change the separate S04 specification.
Source page: Sandwich Panel Handling & Stacking Guide
Read the planning detail
- Actual wall and roof profiles included in the order.
- The agreed size and weight extremes, including protective film if used.
- Pickup, turnover where required, placement and complete-stack removal.
- Surface inspection at the specified contact areas.
- Recipe changes, count confirmation and operator training.
Ask for manuals and a parts list tied to the delivered machine. A generic online manual or an illustrative control-screen image is not sufficient for commissioning or maintenance instructions.
Source page: Sandwich Panel Handling & Stacking Guide
Sandwich Panel Stacker Cost Factors & Quote Scope
Can I use this guide to calculate a fixed machine price?
No. It identifies cost and supply questions. The configuration, covered panel family, delivery conditions and services must be confirmed in the project quotation.
Source page: Sandwich Panel Stacker Cost Factors & Quote Scope
Is the dual-unit price twice the single-unit price?
No such relationship is stated. Synchronization, support, controls, handling range and line integration require a separate proposal; multiplying a single-unit price does not describe that scope.
Source page: Sandwich Panel Stacker Cost Factors & Quote Scope
Are wrapping and bundle removal included?
Only if the quotation explicitly includes those tasks and equipment. Identify the handover, supplier and any option price separately.
Source page: Sandwich Panel Stacker Cost Factors & Quote Scope
Is a published staffing claim enough for a payback estimate?
No. Use your actual baseline and a confirmed proposal with stated assumptions. The site’s brochure case summaries do not provide a verified saving for your factory.
Source page: Sandwich Panel Stacker Cost Factors & Quote Scope
Sandwich Panel Stacker: Selection Input Guide
Panel drawing checklist
| Input | What to provide | Question for the supplier |
|---|---|---|
| Drawing identity | Product name, revision, units, cross-section, edges and joint features. | Which drawing and sample define the proposed configuration? |
| Size and mass | Length, overall and effective width, thickness, rib height and individual weight for each variant. | Which combinations are covered, and which need further review? |
| Faces and finish | Both-face photographs, coating, protective film and panel-maker handling restrictions. | What contact method and contact areas are proposed? |
| Line-exit condition | Upper face, travel direction, leading end, receiving height and current-process video. | What must be retained or changed at the receiving interface? |
Label measured weights and estimates separately, and supply the real product combinations of length, width and weight for each panel.
Source page: Sandwich Panel Stacker: Selection Input Guide
Line and product-change inputs
Attach the cut-off exit, receiving conveyor, stack location and downstream handover on the current layout revision. Record transfer heights, direction, obstructions and retained equipment. Machine outline and complete installed working area are different fields.
Describe observed panel arrival timing, requested targets and the product mix separately. Include stack removal and changes in profile, size, film and bundle arrangement. Ask which changes require recipes, mechanical adjustments or additional tooling.
Use the retrofit checklist for interface responsibilities.
Source page: Sandwich Panel Stacker: Selection Input Guide
Current S01 limits and older references
The current 20261007 single-unit reference gives a normal 2,500–12,000 mm range for stacking only or turnover plus stacking and a 0–2,500 mm stack height. Above 12 m, request a single-unit stacking-only project review, or discuss synchronized dual units if turnover is required.
The older 19 August presentation contains 12 m and 13 m length references; the current model's turnover range follows the 20261007 reference. Identify the current model, motion and actual panel combinations in the proposal.
Ask for the permitted panel family, support arrangement and complete site layout. Dual-unit height, payload, pickup width and panel-thickness values are stated separately; S04 vacuum-stack figures are separate again.
Source page: Sandwich Panel Stacker: Selection Input Guide
Sandwich Panel Stacking Cycle Time & Line Speed
Is nominal cycle time the same as guaranteed throughput?
No. Guaranteed performance, if agreed, must define the panel mix, cycle boundaries, run duration, downstream scope and permitted interruptions in the signed specification.
Source page: Sandwich Panel Stacking Cycle Time & Line Speed
Will the stacker automatically suit any line speed?
No. Review actual arrivals and the complete sequence. The product's nominal cycle alone is insufficient.
Source page: Sandwich Panel Stacking Cycle Time & Line Speed
Does the 2,000 mm stack-height figure describe panel thickness?
No. Stack height and individual panel thickness are different parameters. S04 states 0–2,000 mm stack height and 50–200 mm panel thickness, subject to the project arrangement.
Source page: Sandwich Panel Stacking Cycle Time & Line Speed
Vacuum Pickup for PU Sandwich Panels
Can it handle 15 m panels weighing 450 kg?
15 m and 450 kg are the stated limits; the combined case is checked for the actual panel, support arrangement and motion. Send the longest panel's drawing and measured mass.
Source page: Vacuum Pickup for PU Sandwich Panels
Are all 50–200 mm thick panels suitable?
Thickness is only one input. Face geometry, sealing, stiffness, weight and turnover clearance also need assessment. Confirm each ordered product family.
Source page: Vacuum Pickup for PU Sandwich Panels
Does this replace the product specification?
No. Review the gantry stacker product page and English product PDF for the stated configuration, then obtain a project-specific proposal.
Source page: Vacuum Pickup for PU Sandwich Panels
Tie-Rod Cutting & Welding vs Welding-Only
Can both proposals use the same workpiece list?
Yes, use the same intended assemblies, but state the different incoming conditions and process responsibilities. Otherwise the scopes are not directly comparable.
Source page: Tie-Rod Cutting & Welding vs Welding-Only
Is welding-only always cheaper or faster?
No universal result is established here. Compare the quoted equipment, upstream preparation, handling and agreed output assumptions for the actual project.
Source page: Tie-Rod Cutting & Welding vs Welding-Only
Can I use general pipe-welding specifications for this equipment?
Heating elements, pressure piping, formwork locks and steel-structure tie-rod assemblies have different products and requirements. Use the actual assembly documents and the agreed machine scope.
Source page: Tie-Rod Cutting & Welding vs Welding-Only
Company, documents and delivery
21 questions from 5 pages
About Hebei Pioneer Robot Technology
Who manufactures Color Steel Machine equipment?
Hebei Pioneer Robot Technology Co., Ltd. (河北先行者机器人科技有限公司) in Gaocheng District, Shijiazhuang, Hebei, China. Color Steel Machine is its equipment brand and website.
Source page: About Hebei Pioneer Robot Technology
How many machines are in the catalogue?
Ten machine families in four series: three feeding, four stacking, one packaging and two welding machines. See the specification comparison.
Source page: About Hebei Pioneer Robot Technology
Can I receive company documents with a quotation?
Yes. Ask for the business licence, registered address and the certificates for your machine with your enquiry.
Source page: About Hebei Pioneer Robot Technology
How do I prepare a project discussion?
Use the input guide for your machine and the general quotation preparation guide, then send the completed worksheet with your drawings.
Source page: About Hebei Pioneer Robot Technology
Certificates, Patents & Verification
Which machines do the CAC attestations cover?
The automatic palletizer attestation CAC-M.2026.206.C00599 lists models MFH-S-Z-1200, MFH-X-Q-1200, MCZ-Z-400-01 to 50 and MCZ-Z-300-01 to 50, which include the C/Z purlin stacker MCZ-Z-400-10. The rock wool continuous feeding attestation CAC-M.2026.206.C00579 lists models XM-K-X and XM-L-X.
Source page: Certificates, Patents & Verification
Which patents relate to the stacking machines?
Utility model ZL 2025 2 2003375.X covers a C/Z steel fully automatic turnover stacker, and utility model ZL 2024 2 2396191.X covers automatic profile turnover and stacking equipment. Both name 河北先行者机器人科技有限公司 as patent holder.
Source page: Certificates, Patents & Verification
Who issued the conformity attestations?
CAC Conformity Assessment Center d.o.o. issued both attestations in October 2026, each with a stated five-year validity. They reference Machinery Regulation (EU) 2023/1230.
Source page: Certificates, Patents & Verification
Can I receive copies for my project file?
Yes. The original PDFs are linked on this page. For an order, name the machine model and destination, and the documents for that configuration are prepared with the quotation.
Source page: Certificates, Patents & Verification
Manufacturing & Quality
Which machine and samples does the evidence describe?
Ask for the machine reference, ordered configuration, tooling and sample drawing revision. Note variants that are not represented. A representative sequence should not be presented as proof of all-machine compatibility.
Source page: Manufacturing & Quality
What does a cycle-time or output statement include?
Ask for the counting unit, start and finish points, interruptions and whether loading, replenishment or full-stack removal are included. Nominal brochure values and recorded project results are different evidence.
Source page: Manufacturing & Quality
Does a factory run establish readiness on the buyer’s line?
Site commissioning completes the installation. Identify which interfaces were represented in the trial and which installation, integration or commissioning tasks remain; see the delivery and support workflow.
Source page: Manufacturing & Quality
Where should project acceptance decisions be recorded?
Use the project’s separately agreed protocol and records reviewed by its responsible parties. General website content and downloadable preparation sheets provide no inspection limits, safety approval or sign-off.
Source page: Manufacturing & Quality
Customer Projects
Where do these project summaries come from?
They are project summaries from the manufacturer brochure. Project dates, exact models and operating records are shared on request.
Source page: Customer Projects
Will a similar staffing change apply to my factory?
Your material, line interfaces, operating sequence and baseline are reviewed to estimate the result for your project; the brochure figures describe these reference projects.
Source page: Customer Projects
Which machines relate to these projects?
They provide process-related selection references; the delivered configuration for your project is set in your proposal.
Source page: Customer Projects
Can I see photos or videos of these projects?
Project photos and videos are shared on request, subject to customer approval.
Source page: Customer Projects
Installation, Commissioning & Support
Is overseas installation automatically included?
Export support includes technical documentation and remote support. Overseas attendance, travel costs and response times can be discussed for each project and are stated in the contract.
Source page: Installation, Commissioning & Support
Do downloaded forms confirm capacity or compatibility?
No. They collect project inputs. Equipment configuration, acceptance criteria and operating documentation must match the confirmed machine and application.
Source page: Installation, Commissioning & Support
Does a factory trial replace site commissioning?
No. Agree factory trial conditions and evidence separately from the installed-line interfaces, site readiness and commissioning responsibilities.
Source page: Installation, Commissioning & Support
Can I send drawings through the web enquiry form?
The form accepts a written summary, not attachments. Keep your own file copies and send authorised drawings or videos separately using the email or messaging contacts on the contact page. Downloading a form does not send it to CSM.
File sending guidanceSource page: Installation, Commissioning & Support
Are response times and warranty terms fixed on this page?
Warranty terms, exclusions, response arrangements, spare-parts scope and any attendance are stated in the project contract.
Source page: Installation, Commissioning & Support
Your question is not listed?
Send the product, dimensions, line speed and the manual step you want to automate. The answer depends on your actual line, so the reply is based on your data.
Ask about your lineAutomation glossaryCompare machine specifications